點陣噴碼機噴碼設備墨線偏移的原因與排除

點陣噴碼(ma)(ma)機噴碼(ma)(ma)設備在使用一段時間后，墨線有可能位置會發生微小偏移，墨線位置不正確，導致碼(ma)(ma)印缺字。造成點陣噴碼(ma)(ma)機墨線偏移的原因有，墨路微堵，噴頭微堵，充電槽、壓力的問題。

若點陣噴碼機只是墨線微小偏移，可按以下進行調整。一、墨線向前偏，將調節螺絲向左微調。二、墨線向后偏，將調節螺絲向右微調。三、墨線向左偏，將凸輪機構向右微調。四、墨線向右偏，將凸輪機構向左微調。

墨線偏移解決：

（一）、墨路微堵，先檢查過濾器，過濾器是否正常，過濾網是否完好，若不正常，更換過濾器；點陣噴碼(ma)機具備自動清洗功能，在機器上清洗，清洗墨路、清洗喉管，沖洗，可連續多次開關清洗功能。

（二）、噴頭微堵，多次連續開關噴嘴的方法去沖開噴嘴。若行不通，清洗噴嘴，還可拆掉噴嘴在超聲波里震動清洗里清洗。

（三）、充電槽、壓力的問題。噴頭外殼的放大鏡觀察墨線在充電槽中的位置是否在正中間且平行，平行，則墨線調整完成；不平行，則調整充電槽的位置。一、稍微松開充電槽支架螺絲；二、根據剛墨線在充電槽的位置，輕輕地搬動充電槽，調整好以后擰緊充電槽支架螺絲。注意在搬動充電槽時，一定要輕輕搬動，否則墨水會搞得一塌糊涂。